CompuSTAR 1W900SHR-961 Manual de instalación descargar pdf (Pagina 6)

Placement and Use of Components

IMPORTANT: The placement and use of components are critical to the performance of this system.

Antenna and Cable

Firstech antennas are calibrated for horizontal

installation at the top of the windshield. The cable that

connects the antenna to the control module must be

free from any pinches or kinks. Installing the antenna in

areas other than the windshield may adversely affect

the effective transmitting distance of the remotes.

RPS-II (Remote Paging Sensor)

(CM4000, CM5000, and CM4300 Only) The RPS-II sensor is designed to be mounted on the inside of

the windshield. Basic RPS functions do not require programming. There is a three position switch on the

rear of the RPS-II. This adjusts the sensitivity of the RPS-II. The larger the circle the more sensitive the

knock is. To activate the RPS unlock / disarm feature you must perform the following procedures:

STEP 1: Disarm/unlock the alarm. (Remotes must be programmed first.)

STEP 2: Turn ignition key to the “on” position and the leave the driver’s door open.

STEP 3: Knock on the windshield in front of the RPS a total of 10 times (each time you knock the LED on the RPS will flash

RED). The LED will begin to flash rapidly in BLUE with successful completion of this step.

STEP 4: Enter the first digit of the desired four-digit pass code by knocking on the windshield in front of the RPS the desired

number of times. For example, to enter 3, knock on the sensor 3 times (each time you knock the LED will flash RED) then wait.

STEP 5: The LED on the RPS will confirm your first number by flashing BLUE slowly. Once the LED begins to flash rapidly in

BLUE, enter your second number by repeating step 4.

STEP 6: Repeat steps 4 & 5 to enter all four numbers.

STEP 7: Turn the ignition OFF. The RPS disarm/unlock feature is now programmed. Repeat steps 3 – 5 to enter your

disarm/unlock code.

**The first two digits of the RPS unlock/disarm pass code will be the default pass code for the Secure Valet (you do not

need to program them independently).

Secure Valet Switch

The optional Secure Valet Switch prevents the alarm from being put into valet mode through cycling the

ignition on/off five times. The Secure Valet Switch is more secure than traditional toggle / valet switches

because it requires a two digit code. To program this feature you must perform the following procedures:

STEP 1: Turn on Option 3-10-III.

STEP 2: Turn ignition key to the “on” position.

STEP 3: Hold down the valet switch for 1.5 seconds. The LED on the valet switch will begin to flash rapidly with successful

completion of this step.

STEP 4: Enter the first digit of the desired two-digit pass code by depressing the switch the number of times that coordinates

with the desired first number. For example, to enter 3, depress the switch 3 times, then wait.

STEP 5: The LED will confirm the first number by flashing BLUE slowly. Once the LED begins to flash rapidly, enter your second

number by repeating step 4.

STEP 6: Turn the ignition off - the Secure Valet Switch is now programmed. Follow steps 3 – 5 to enter your Secure Valet code.

**The first two digits of the RPS unlock/disarm pass code will be the default pass code for the Secure Valet (you do not

need to program them independently).

Firstech Shock Sensor

(CM4000, CM5000, and CM4300 Only) For best results mount the shock sensor by zip tying it to the

vehicles main ignition harness. There is a small dial on the sensor that ranges from Off to 10. The higher

the number on the dial the greater sensitivity of impact. A small adjustment to the dial can make a

Antenna

RPS-II

1 2 3 4 5 6 7 8 9 10 11 ... 35 36

Comentarios a estos manuales

Sin comentarios

CompuSTAR 1W900SHR-961 Manual de instalación Pagina 6

Comentarios a estos manuales

Relacionado con productos y manuales para Controles remotos CompuSTAR 1W900SHR-961