CompuSTAR CM4200DX Guía de instalación descargar pdf (Pagina 9)

6. You will need to first identify what COM port your USB device is set up to use. To do this, Right-click on "My

Computer" and go to "Properties". Once the properties window is on the screen, click the "Hardware" tap at the

top of the window. Then in the main body of the window, click on the Device Manager" button. Under "Ports

(COM & LPT)" There should be a device called "USB Serial Port (COM?)", the number that is in place of the

question mark is your selected com port. Disconnect the main harness; the system can not have power while

you are attempting to update its software.

7. The Secure Valet Switch must be connected.

8. Connect the USB-DC2 or modified cable to the RS232 port of CompuStar.

9. Open the "CM4000 v12" folder, for example, and hold the LED/Valet switch button down while you double-

click the file that matches your com port. Example: I use COM5 so I would use "Update-COM5.bat". Once the

LED in the LED/Valet switch starts flashing, you can let go of the button. After it is finished, just disconnect

the CM4200-DX from the USB Updater and connect the next CM4200-DX if you have more to do.

________________________________________________________________________________________________

ADDITIONAL ITEMS TO INSTALL

These accessories must be installed and programmed to ensure full functionality of the system.

Important Note: Before you make all your wire connections and connect the additional items please review the

Option Programming Tables and the descriptions at the end of this manual.

Antenna (CN8)

Usually mounted in the top left or center of the front windshield. It can be mounted in any orientation, horizontal or

vertical. Stay at least 1.5 inches away from metal and try to mount below the tint stripe. Once all your Control Module

connections are made and antenna connected you can program the remote(s).

Antenna Cable (CN8)

The antenna cable should be routed to the antenna with care. Try not to pinch or crimp the cable on panels as the

system could experience poor range, poor remote communication or no functionality at all.

Remote Coding Procedure

Once the above wire connections have been made and antenna has been connected, you are ready to program your

remotes. The Control Module can accept up to 3 remotes with the exception of the 2WSSR Pro. The following includes

procedures for programming 1-Way and 2-Way remotes:

1. Cycle the key in the ignition from the “Off” to the “On” position 5 times. This must be done within 7

seconds.

2. After the 5

cycle, you will hear the parking light relay “click” and see the parking lights flash once. Be

aware that the vehicle’s “chime” may prevent you from hearing the relay “click.”

3. Once you hear two relay clicks along with two parking light flashes, the system has just exited remote

coding mode. (Note: If no remotes are programmed at this point then the CompuStar will automatically

enter Valet Mode.)

4. Right after cycling the ignition the 5 times:

a. 1-Way Remote: Tap the lock button on the remote for a split (0.5) second.

b. 2-Way Remote: Tap button I for a split (0.5) second.

c. 2-Way Spread Spectrum Remote – This remote requires a different procedure for programming

I. Remove the (+) positive side of the battery from the remote.

II. Follow steps 1 to 3 above.

III. Slide (+) positive side of remote battery back into remote.

IV. Do not press any buttons on the remote as it is syncing with the antenna.

V. Once the remote receives a page back, the 2WSSR is ready for use.

5. After tapping the button on the remote, you will hear the parking light relay “click” once to indicate that it

has accepted the remote. If you have other remotes you must program them at the same time, repeat steps 4a

or 4b for each remote you have.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 ... 21 22

Comentarios a estos manuales

Sin comentarios

CompuSTAR CM4200DX Guía de instalación Pagina 9

Comentarios a estos manuales

Relacionado con productos y manuales para Arrancadores remotos CompuSTAR CM4200DX