CompuSTAR CM4200DX Guía de instalación descargar pdf (Pagina 15)

To change the option number you wish to program, use the left and right arrow keys on the OP-500, it will

scroll through the options available in menu 1 and then move to menu 2, then 3 and 4. At the end of menu 4, if

you have turned on diesel mode or the channel expander, or set any of the auxiliary outputs to “Program”, you

will have the option to program the duration of the diesel timer and/or auxiliary outputs. After the aux and

diesel settings (if selected), the POC options will be displayed. The “POCs” are the programmable outputs on

CN3 of the Pro-Series modules.

You can then use the up and down arrow buttons to adjust the option’s settings. “1” is the default setting, and

“2”, “3”, and “4” are the optional settings. The timing of the aux outputs and of the diesel timer is displayed in

seconds, and the POCs can be set between 0 (default) and 12. If you wish to restore all of the factory defaults,

you can press “R” and “W” until the OP-500 chirps.

3. Finalizing Option Settings to Control Module

When you are done adjusting the various option settings or resetting them to the factory defaults, press and hold

the “W” (write) button until the OP-500 chirps. This will write the settings to the control module. Wait until the

module displays “Success” before disconnecting it from the antenna cable.

Updating the OP-500

This is required only if you have an early version of the Option Programmer OP-500.

1. To retrieve software for updating please email: [email protected]. Please write “request for update

software” in subject. You can also go to www.compustar.com

2. You will need to first identify what COM port your USB device is set up to use. To do this, Right-click on

"My Computer" and go to "Properties". Once the properties window is on the screen, click the "Hardware" tap

at the top of the window. Then in the main body of the window, click on the Device Manager" button. Under

"Ports (COM & LPT)" There should be a device called "USB Serial Port (COM?)", The number that is in

place of the question mark is your selected com port.

3. Connect the USB Updater to the computer, do not have anything (iDataLink, CM4000, OP500 etc) connected

to the updater when connecting it to the computer. After a few seconds, connect the USB Updater to the "USB"

port on the OP500 using the supplied cable. Open the "OP500 v6.2" folder and hold the "W" button on the

OP500 down while you double-click the file that matches your com port.

Example: I use COM5 so I would use "UPDATE-V6-COM5.bat". Once the OP500 displays "UP" on the screen,

you can let go of the "W" button. After it is finished, just disconnect the OP500 from the USB Updater and

connect the next OP500 if you have more to do.

________________________________________________________________________________________________

PTION PROGRAMMING TABLES

Note: Option Programming, RPS Programming and Secure Valet Programming are available only when the system is

disarmed/unlocked.

Special Option Group #1 and #2 can only be programmed with the Option Programmer OP500.

OPTION GROUP 1

Setting Applicable To

Feature

Default(I) Optional(II) Optional(III) Optional(IV)

CM4000 CM4200-DX CM4300

1-1 Unlock before, Lock after, starting. Off On

Lock After Remote Start

Only

V V

1-2 Lock / Unlock pulse duration. 0.8 sec 2.5 sec 0.125 sec 3.5 sec

V V V

1-3 Driver's priority unlock Off On

V V V

1-4 Double pulse unlock. Off On

V V V

1-5 Rearm Output

After Start Shutdown and

First Lock

After Start Shutdown and

Every Lock

V V V

1-6 Reservation Lock (Manual transmission)

Locks When Reservation

Mode is Set

Does Not Lock When

Reservation is Set

Reservation Sets 10 Seconds

After the Last Door is Closed

V V

1 2 ... 10 11 12 13 14 15 16 17 18 19 20 21 22

Comentarios a estos manuales

Sin comentarios

CompuSTAR CM4200DX Guía de instalación Pagina 15

Comentarios a estos manuales

Relacionado con productos y manuales para Arrancadores remotos CompuSTAR CM4200DX