CompuSTAR CM4200DX Guía de instalación descargar pdf (Pagina 21)

This option controls the trigger of the Aux output. These are optional event triggers. Default setting triggers Aux 1

by the remote. Setting 2 triggers Aux 1 by remote and arming of the system. Setting 3 triggers Aux 1 by remote and

disarming of the system. Setting 4 triggers Aux 1 through panic of the system.

4-4 Aux 2 output Control

This option controls the trigger of the Aux output. These are optional event triggers. Default setting triggers Aux 2

by the remote. Setting 2 triggers Aux 2 by remote and arming of the system. Setting 3 triggers Aux 2 by remote and

disarming of the system. Setting 4 triggers Aux 2 through panic of the system.

4-5 Secure Aux Output (Aux 1 and Aux 2 Only)

With this option on the default setting you must first tap button 4 on the remote and then tap either button 2 or 3 to

activate Aux 1 or Aux 2. This is to prevent accidental triggering of Aux 1 or 2 if they are hooked up to door

poppers or window modules. On optional setting 2 this turns the secure aux off.

4-8 Extended Accessory After Ignition Shutoff

With this setting you can set the system to keep the Accessory wire powered up after you shut the ignition off. This

can be used to keep the radio powered up for a certain amount of time. Setting 2 keeps the Accessory on for 10

seconds. Setting 3 keeps the Accessory on for 30 seconds. Setting 4 keeps the Accessory on until you open the

door. The maximum time for setting 4 option is 1 minute.

4-9 Key Sense or Glow Plug Input

This option changes the setting of the key sense/glow plug input wire on CN3. Default setting sets the wire as a

glow plug input wire. Setting 2 changes the wire into a key sense input. The key sense input can be used to prevent

setting reservation (manual transmission) and passive arming while the key is still in the ignition.

4-10 Trigger Start or Closed Loop System Input

This option changes the setting of the trigger start input wire on CN3. Default setting is the trigger start when using

the control module as a slave unit. Setting 2 changes the wire into a closed loop system. The wire becomes an

instant trigger if the wire is separated from ground. (-) This can be used for headlights housings or connected to a

tow hitch.

Special Option Group 1

This option group controls the Diesel Timer and Aux 1 though 7. Aux 3 through 7 are only available with the

Channel Expander. The Diesel Timer can only be set for 3 to 99 seconds. Aux 1 through 7 can be set from 1 to 100

seconds. This option group can only be accessed with the OP500 Option Programmer.

Special Option Group 2

This option group controls the Programmable Output Connectors. (POC) The POCs are located on CN3. (please see

wiring guide for more details) This option group can only be accessed with the OP500 Option Programmer. At

default setting each option will read “0.” You can set each POC to 1-12. This changes the function of the POCs.

Please see the option menu and wiring guide for details of each POC.

________________________________________________________________________________________________

LIMITED LIFETIME CONSUMER WARRANTY

Firstech, LLC. warrants to the original purchaser that this product shall be free of defects in material and workmanship

under normal use and circumstances for the period of time that the original owner of this product owns the vehicle in

which it is installed; except that the remote controller unit for the period of one year from the date of installation to the

original owner of this product. When the original purchaser returns the product to the retail store where it was

purchased or prepaid postal to Firstech, LLC., 21911 68

Avenue South – Kent, WA 98032, USA within the warranty

period, and if the product is defective, Firstech, LLC., will at its option repair or replace such.

1 2 ... 16 17 18 19 20 21 22

Comentarios a estos manuales

Sin comentarios

CompuSTAR CM4200DX Guía de instalación Pagina 21

Comentarios a estos manuales

Relacionado con productos y manuales para Arrancadores remotos CompuSTAR CM4200DX