CompuSTAR 1WAMR-Fiance Manual de instrucciones descargar pdf (Pagina 39)

3.

Install

the

VSM200/250

or

DSM200/250

using

the information in the

wiring

diagram

and

steps

(Note

CAUTIONS

during

installation).

a. Configuration Wires: Connect the

loose

gray

or

white configuration wire(s) to match the

desired

application

(see

table below).

MODE

GRAY

WIRE

WHITE

WIRE

ESP2

Open Open

D2D,

RSR/RXT

GND

Open

Autos

tart/ AstroStart

Open

GND

b. Connect the

serial

data

cable

and adapter to

the correct port

of

the main module.

For D2D

RSR/RXT

applications,

connect the

serial

data

cable and

adapter

to Xpresskit

module.

c.

Complete the main

power

connections.

d.

When

power

is

connected, the module

be-

gins an

initialization

procedure that may

take several

minutes. During this procedure,

progress

is

reported via the

flashing

Amber/

Green

LEDs

next to the

module cable.

When

both

LEDs

turn on solid,

the initialization

pro-

cedure

is

completed

(See

Status

LEOs

for a

description

of

the various

LED

states).

4 .

Verify

and

Activate the SmartStart

module:

The

following

steps

need to be performed for the

Verification/

Activation

of

the Directed SmartStart

module.

2

a. Collect

Customer Information:

Customer's

Full

Name:

Customer's E-mail

Address:

Customer's

mobile

phone#

and

phone carrier

Record/place

Module

ID

#here:

New

Account:

D

Existing Account:

D

If

this

is

an

ex

isting account, are you:

adding

a

new

system:

D

or

replacing

an

existing one:

D

b.

Log

on to:

www

.directechs.com,

and

click

on

the SmartStart

link.

c.

Follow

the on-screen directions to activate

and test a SmartStart device.

If

this

is

the

cus-

tomer's

first SmartStart system, you

will

be

prompted to enter their information as col-

lected

in

step

4a

.

d.

Set

configuration for commands to match the

installed application.

e.

Test

the SmartStart

system

from the website

using the supplied

function

links.

f.

The

customer

is

sent

log-in

information via

e-mail.

After

logging

into the site

at

www

.

mysmartstart.com, they must

select and

pay

for the service

plan

in

order

to start using the

system.

Status

LEDs

Amber

LED

states:

•

Off:

No

cellular communication. Check

connections

such

as

module

harness.

• Flashing slowly:

The

module

is

seeking

cellular

system

communication.

If

no

cell

coverage

is

available

the Amber

LED

continues to

flash slowly,

move the

veh

ide

to a

location

with better reception.

• Flashing quickly:

The

module

is

negotiat-

ing with a

cellular

system .

•

On

solid:

Communication

successfully

es-

tablished.

Green

LED

states:

•

Off:

Communication not

established

with

the remote start main unit

or

no

serial

de-

vice

is

connected.

Check connection

at

the Bitwriter port,

once connected properly the

LED

turns on

after resetting the

power

to the SmartStart

module.

•

On

solid:

Communication

successfully

es-

tablished

with the remote start main unit.

Please

return this

guide

and

point the customer to

steps

4a

and

4f

after

successfully completing

the in-

stallation

as it contains

details

required for account

setup.

Notes: SmartStart response time can

vary

depend-

ing on cellular

coverage

and

network congestion.

Operating

temperature range:

-

30

°C

to

+

70

oC.

Additional information

can be found at:

www

.directechs.com

EL

E C

TRONIC

S

©

20

11

Dir

ected

Elec

tr

o

ni

cs

.

All

rights

re

served.

1 2 ... 34 35 36 37 38 39 40 41 42 43 44

Comentarios a estos manuales

Sin comentarios